</a>智能傳感器" title="智能傳感器">智能傳感器" title="智能傳感器">智能傳感器STPMS2的演示板,設計和姐妹片STPMC1的STEVAL-IPE010V1演示板一起用于能量表.而STPMS2是一款智能傳感器,采用Rogowski線圈,電流變壓器,霍爾或分流傳感器來測量動力線系統的能量,VCC電壓3.2V-5.5V,集成兩兩個二階sigma-delta (ΣΔ)調制器,支持50-60 Hz, EN 50470-1, EN 50470-3, IEC 62053-21, IEC 62053-22等標準,適用于電表,馬達控制,工業過程控制,稱重表和壓力傳送器.本文介紹了STPMS2主要特性,方框圖和應用電路圖,以及STEVAL-IPE014V1演示板特性,電路圖和材料清單.
The STPMS2, also called “smart sensor” devices, are ASSPs designed for effective measurement in power line systems utilizing Rogowski coil, current transformer, Hall or shunt sensors. These devices are designed as building blocks for single-phase or multi-phase energy meters along with the STPMC1 device, a digital signal processor designed for energy measurement. This device can be used in medium and high resolution measurement applications where single or double inputs must be monitored at the same time. The STPMS2 are mixed signal ICs consisting of an analog and digital section. The analog section consists of a programmable gain, low noise choppered amplifier, two second-order ΔΣ modulator blocks, a band-gap voltage reference, a low-drop voltage regulator and DC buffers, while the digital section consists of a clock generator and output multiplexer.
The STPMS2 is a device designed to measure electrical line parameters (voltage and current) via analog signals from voltage sensors (current divider) and current sensors(inductive Rogowski coil, current transformer or shunt resistors). The device is used together with a digital signal processing circuit to implement an effective measuring system for multi-phase power meters.
The device consists of two analog measuring channels, consisting of second-order sigmadelta modulators with appropriate non-overlapping control signal generator. The STPMS2 also includes a temperature compensated band-gap reference voltage generator, a lowdrop supply voltage stabilizer and minimal digital circuitry that includes BIST (built-in selftest) structures. In a current signal processing channel, a low-noise preamplifier is included in front of the sigma-delta converter. All reference voltages (band-gap, AGND) are internally buffered to eliminate channel crosstalk.
The STPMS2 can operate in fast or low-power mode. In fast mode, a nominal clock frequency of 4.1 or 4.9 MHz is applied to the clock input. In this mode, signal bandwidth is specified between 0 and 4 kHz. In low-power mode, the nominal clock is four times slower in order to reduce the power consumption of the circuit. In low-power mode, the quiescent bias currents of the preamplifier and sigma-delta integrators are lowered and the signal bandwidth is narrowed to the frequency bandwidth of 0 to 1 kHz.
STPMS2主要特性:
■ VCC supply range 3.2 V - 5.5 V
■ Two second-order sigma-delta (ΣΔ) modulators
■ Programmable chopper-stabilized low noise and low offset amplifier
■ Supports 50-60 Hz, EN 50470-1, EN 50470-3, IEC 62053-21, IEC 62053-22 and IEC 62053- 23 standards specs for class 1, class 0.5 and class 0.2 AC watt meters
■ STPM02H: less than 0.5% error over 1:10000 range
■ STPM02L: less than 0.5% error over 1:5000 range
■ Precision voltage reference: 1.23 V with programmable TC (STPMS2L only)
■ Internal low drop regulator @ 3 V (typ.)
STPMS2應用:
■ Power metering
■ Motor control
■ Industrial process control
■ Weight scales
■ Pressure transducers
圖1. STPMS2方框圖
圖2. STPMS2應用電圖
圖3. 基于STPMC1的簡化電表應用電路圖
STEVAL-IPE014V1演示板
The STEVAL-IPE014V1 is a demonstration board designed for the STPMS2L chip. It is designed to work along with the STEVAL-IPE010V1 demonstration board, for a ready-touse energy meter application.
The STEVAL-IPE010V1 demonstration board is for the STPMC1 device, while the IPE014 package contains only the daughterboard with the STPMS2L companion chip.
These demonstration boards can be used in two ways:
■ For demonstration purposes. Connecting the reference design to an AC power source and changing all the settings parameters through the GUI interface and the parallel hardware programmer/reader
■ For user application demonstration and development
圖4.STEVAL-IPE014V1演示板外形圖
STEVAL-IPE014V1
This board is a daughterboard. Each module serves one single phase, converting the voltage and current information, multiplexing them together, and sending the stream to the STPMC1.
Each of the boards must be connected to the voltage source of the relative phase and to the load.
Test points available are:
● GND
● VCC (stepper counter display connector)
● CLK
● DAT
● VREG
● F, N
The board should be plugged into the motherboard by the edge connector. Voltage inputs are pin F (hot wire) and N (neutral wire).
Current input (load wire) should be passed through the current transformer placed on the non-component side of the module.
圖5.STEVAL-IPE014V1電路圖
STEVAL-IPE014V1材料清單:
詳情請見:
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00253175.pdf
和
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/USER_MANUAL/DM00023358.pdf
The STPMS2, also called “smart sensor” devices, are ASSPs designed for effective measurement in power line systems utilizing Rogowski coil, current transformer, Hall or shunt sensors. These devices are designed as building blocks for single-phase or multi-phase energy meters along with the STPMC1 device, a digital signal processor designed for energy measurement. This device can be used in medium and high resolution measurement applications where single or double inputs must be monitored at the same time. The STPMS2 are mixed signal ICs consisting of an analog and digital section. The analog section consists of a programmable gain, low noise choppered amplifier, two second-order ΔΣ modulator blocks, a band-gap voltage reference, a low-drop voltage regulator and DC buffers, while the digital section consists of a clock generator and output multiplexer.
The STPMS2 is a device designed to measure electrical line parameters (voltage and current) via analog signals from voltage sensors (current divider) and current sensors(inductive Rogowski coil, current transformer or shunt resistors). The device is used together with a digital signal processing circuit to implement an effective measuring system for multi-phase power meters.
The device consists of two analog measuring channels, consisting of second-order sigmadelta modulators with appropriate non-overlapping control signal generator. The STPMS2 also includes a temperature compensated band-gap reference voltage generator, a lowdrop supply voltage stabilizer and minimal digital circuitry that includes BIST (built-in selftest) structures. In a current signal processing channel, a low-noise preamplifier is included in front of the sigma-delta converter. All reference voltages (band-gap, AGND) are internally buffered to eliminate channel crosstalk.
The STPMS2 can operate in fast or low-power mode. In fast mode, a nominal clock frequency of 4.1 or 4.9 MHz is applied to the clock input. In this mode, signal bandwidth is specified between 0 and 4 kHz. In low-power mode, the nominal clock is four times slower in order to reduce the power consumption of the circuit. In low-power mode, the quiescent bias currents of the preamplifier and sigma-delta integrators are lowered and the signal bandwidth is narrowed to the frequency bandwidth of 0 to 1 kHz.
STPMS2主要特性:
■ VCC supply range 3.2 V - 5.5 V
■ Two second-order sigma-delta (ΣΔ) modulators
■ Programmable chopper-stabilized low noise and low offset amplifier
■ Supports 50-60 Hz, EN 50470-1, EN 50470-3, IEC 62053-21, IEC 62053-22 and IEC 62053- 23 standards specs for class 1, class 0.5 and class 0.2 AC watt meters
■ STPM02H: less than 0.5% error over 1:10000 range
■ STPM02L: less than 0.5% error over 1:5000 range
■ Precision voltage reference: 1.23 V with programmable TC (STPMS2L only)
■ Internal low drop regulator @ 3 V (typ.)
STPMS2應用:
■ Power metering
■ Motor control
■ Industrial process control
■ Weight scales
■ Pressure transducers
圖1. STPMS2方框圖
圖2. STPMS2應用電圖
圖3. 基于STPMC1的簡化電表應用電路圖
STEVAL-IPE014V1演示板
The STEVAL-IPE014V1 is a demonstration board designed for the STPMS2L chip. It is designed to work along with the STEVAL-IPE010V1 demonstration board, for a ready-touse energy meter application.
The STEVAL-IPE010V1 demonstration board is for the STPMC1 device, while the IPE014 package contains only the daughterboard with the STPMS2L companion chip.
These demonstration boards can be used in two ways:
■ For demonstration purposes. Connecting the reference design to an AC power source and changing all the settings parameters through the GUI interface and the parallel hardware programmer/reader
■ For user application demonstration and development
圖4.STEVAL-IPE014V1演示板外形圖
STEVAL-IPE014V1
This board is a daughterboard. Each module serves one single phase, converting the voltage and current information, multiplexing them together, and sending the stream to the STPMC1.
Each of the boards must be connected to the voltage source of the relative phase and to the load.
Test points available are:
● GND
● VCC (stepper counter display connector)
● CLK
● DAT
● VREG
● F, N
The board should be plugged into the motherboard by the edge connector. Voltage inputs are pin F (hot wire) and N (neutral wire).
Current input (load wire) should be passed through the current transformer placed on the non-component side of the module.
圖5.STEVAL-IPE014V1電路圖
STEVAL-IPE014V1材料清單:
詳情請見:
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00253175.pdf
和
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/USER_MANUAL/DM00023358.pdf
本站內容除特別聲明的原創文章之外，轉載內容只為傳遞更多信息，并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題，請及時通過電子郵件或電話通知我們，以便迅速采取適當措施，避免給雙方造成不必要的經濟損失。聯系電話：010-82306118；郵箱：aet@chinaaet.com。